LEADING 10 COMMON FORKLIFT ACCIDENTS , FORKLIFT PROCEDURE SHOULD PAY ATTENTION TO THESE MATTERS !.

Leading 10 common forklift accidents , forklift procedure should pay attention to these matters !.

Leading 10 common forklift accidents , forklift procedure should pay attention to these matters !.

Blog Article


Don't ignore the forklift at the workplace. If the procedure is not good, there will be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when lifting hefty items, the workers used their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift motorist did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these issues :.

Start.
1. Prior to starting, observe the surroundings, and after verifying that there are no obstacles that impede the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly impact the stability of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when stacking or loading. .
8. The height of the load should not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should be against the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it Stand-on Electric Pallet Stacker ought to be kept in mind that the fork tip must not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide Electric Forklift Truck for Warehouse with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance ought to be checked, and fuel, lubing oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the stress and temperature are normal.
5. After the forklift is running, the outside leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize braking force to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web:https://www.onenforklifts.com/
Email:info2@onen.cn
Phone:+86 13827083844

Report this page